gbf1671
gbf1671

Guardian Recessed Emergency Shower, Recess Mounted Shower Head MODEL : GBF1671

Barrier-Free WideArea™ Eye/Face Wash, Pedestal Mounted, Arca Timur GUARDIAN BARRIER-FREE WIDEAREA EYE/FACE WASH, PEDESTAL MOUNTED MODEL : GBF1704
Eyewash/Drench Hose Unit, Wall Mounted, 12 Coiled Hose, Ball Valve with Flag Handle, Arca Timur Guardian Eyewash/Drench Hose Unit, Wall Mounted, 12’ Coiled Hose, Ball Valve with Flag Handle MODEL : G5014

Application: Recessed emergency shower with ceiling mounted recessed shower head. Recessed shower conserves valuable floor space, while eliminating the clutter and obstruction created by conventional shower equipment. Unit can be installed in either a corridor or a lab room, close to where accidents might occur.

ADA Compliance: When installed at recommended mounting heights, unit complies with ADA requirements for accessibility by handicapped persons.

Shower Head: 10” diameter stainless steel with 20 GPM flow control and flange for flush mounting in ceiling.

Valve: 1″ IPS brass stay-open ball valve with stainless steel “panic bar.” Pulling bar down activates shower; shower remains in operation until bar is returned to original closed position. Furnished with stainless steel access panel and 1″ IPS unions for valve.

Mounting: 16 gauge stainless steel cabinet with flange featuring 3/8” return for recessed mounting in wall.

Supply: 1″ NPT female inlet.

Sign: ANSI-compliant identification sign.

U.S. Patent 5,768,721

Note: ANSI Z358.1-2014 specifies that shower heads be installed no more than 96″ above the finished floor. This unit should therefore not be installed in ceilings over 8 feet. For higher ceiling heights, we recommend either the GBF1670 or GBF1672 showers.

SKU: GBF1671 Categories: ,
  • Description
  • Downloads

Description

AVAILABLE OPTIONS

  • AP250-065 Modesty curtain for wall mounting.
  • AP280-235 Electric strobe light and alarm horn unit for recess mounting in finished wall. Light illuminates and horn sounds when shower is activated. Includes additional leads for remote monitoring.
  • G3800LF Thermostatic mixing valve precisely blends hot and cold water to deliver warm (tepid) water as required by ANSI Z358.1-2014. Refer to Tempering Valves section for complete technical and product selection information.

Technical information

Catalog Page

Parts / O&M

Written Specs

Related Products

  •
    Read more
    Quick View

    GUARDIAN HEATED SAFETY STATION WITH EYEWASH, TOP INLET, RATED FOR CLASE I, DIVISION 2 ENVIRONMENT MODEL : GFR3100
    Guardian Safety – Heated Safety Station with Eyewash, Top Inlet, Rated for Class I, Division 2 Environment

    Application: Electric heat-traced stations prevent freezing even in extreme conditions. Thermostat regulated units are heated by self-limiting heat-tracing cable wrapped around internal pipe. Units are intended for cold weather use down to -40°F. See ‘Tempering Valves’ section to ensure tepid water compliance with ANSI Z358.1-2014.

    Heating Cable: Self-regulated with external termination guards. Thermostat activates when internal piping temperature falls below 75°F. FM, UL, and CSA approved for Class I, Division 2, Groups B, C, and D.

    Electrical System: Unit is fully wired at factory. Junction box and components rated for Class I, Division 2, Groups B, C, and D. Requires 120 VAC single phase power supply.

    Jacket/Insulation: UV-resistant orange ABS plastic with polyethylene foam insulation. Jacket sections secured with removable stainless steel screws for easy maintenance.

    Shower Head: 10″ diameter orange ABS plastic with 20 GPM flow control.

    Shower Valve: 1″ IPS brass stay-open ball valve. US-made with brass ball and PTFE seals. Includes stainless steel actuating arm and 29″ stainless steel pull rod.

    Spray Head Assembly: Freeze-resistant with float-off dust covers and internal flow control.

    Eyewash Valve: 1/2″ IPS brass three-way self-draining stay-open ball valve. US-made with brass ball and PTFE seals. Includes 1/2″ NPT port to drain water from spray heads after use.

    Pipe And Fittings: Schedule 40 galvanized steel.

    Supply: 1-1/4″ NPT female top inlet.

    Sign: ANSI-compliant identification sign.

    Quality Assurance: Factory tested prior to shipment. Ships fully assembled and crated.

    Read more
    Quick View
  •
    Read more
    Quick View

    GUARDIAN MODESTY CURTAIN FOR RECESSED LABORATORY UNITS MODEL : AP250-065

    Application: In an emergency, it is imperative that contaminated clothing be removed as quickly as possible. However, employees may be reluctant to remove their clothing in the presence of co-workers. A modesty curtain will protect the privacy of the user and permit disrobing while the shower unit is in operation. The curtain has a pocket in which a smock can be stored.

    Installation: Unit is designed for use with recessed laboratory units, including emergency showers and combination safety stations. Furnished complete with stainless steel track assembly for wall mounting. All necessary mounting brackets are included.

    Curtain: White polyester curtain with ring hangers. Curtain has tie-back so it can be neatly stored when emergency equipment is not in use. Curtain has interior pocket for storing a smock to be used after contaminated clothing is removed.

    Read more
    Quick View
  •
    Read more
    Quick View

    GUARDIAN TEMPERING VALVE, 6 GALLON CAPACITY MODEL : G3600LF

    Mixing valve, thermostatic, for eyewash assembly, blends hot and cold water to deliver warm (tepid) water, use with G1814BC eyewash unit, sold by the each

    Read more
    Quick View
  • Eyewash/Drench Hose Unit, Wall Mounted, 12 Coiled Hose, Ball Valve with Flag Handle, Arca Timur
    Read more
    Quick View

    Guardian Eyewash/Drench Hose Unit, Wall Mounted, 12’ Coiled Hose, Ball Valve with Flag Handle MODEL : G5014

    Application: Dual purpose eyewash/drench hose with ball valve and flag handle for wall mounting. Unit meets the provisions of ANSI Z358.1-2014 as both an eyewash and a drench hose. Unit may be left in the mounting bracket for use as a fixed eyewash, leaving user’s hands free. Alternatively, unit may be removed for use as a drench hose to rinse any part of user’s eyes, face or body. 12’ nylon retractable hose coils to eliminate trip hazard.

    Spray Head Assembly: Two GS-Plus™ spray heads mounted side-by-side. Each head has a “flip top” dust cover, internal flow control and filter to remove impurities from the water flow.

    Valve: 1/2″ IPS chrome plated brass stay-open ball valve. Valve is US-made with chrome plated brass ball and PTFE seals.

    Hose: 12′ reinforced nylon retractable coiled hose. 180 PSI maximum working pressure.

    Mounting: Bracket with spring clips to hold unit on wall. Clips assure that spray heads face forward at all times.

    Supply: 3/8″ NPT female inlet.

    Sign: ANSI-compliant identification sign.

    Quality Assurance: Unit is completely assembled and water tested prior to shipment.

    Read more
    Quick View
  • 15 Gallon Portable Eyewash/Drench Hose Unit with Heated Orange Insulation Jacket, Arca Timur
    Read more
    Quick View

    GUARDIAN 15 GALLON PORTABLE EYEWASH/DRENCH HOSE UNIT WITH HEATED ORANGE INSULATION JACKET MODEL : G1562HTR

    Application: Self-contained eyewash/drench hose unit is ideal for use in low traffic areas, and where a continuous supply of potable water is unavailable for plumbed units. Unit is heated and insulated to endure low or freezing temperatures over long periods of time. Unit is fully freeze-resistant and tempered, for both indoor and outdoor environments. 15 gallon pressurized unit is ideal for floor placement near any hazard, and delivers approximately 10 usable gallons (37.9 liters) of water for 15 minutes, thus complying with the provisions of ANSI Z358.1-2014 for eyewashes.

    Tank And Jacket: 15 gallon stainless steel pressurized tank with 10 gallons (37.9 liters) usable capacity. Tank has built-in carrying handles, Schrader air intake valve, pressure gauge and pressure relief valve. Highly visible orange Diener Nylon insulation jacket is waterproof and mildew resistant.

    Heating Element: Silicone drum heater is attached to the tank with a spring latch. Water temperature inside of the tank is regulated by an onboard thermostat set to 65°F. Total amp draw is 3.33A and delivers 400W of power, which allows the unit to operate to temperatures as low as -20°F.

    Ground Fault Plug: Unit comes standard with a 15A Ground Fault Circuit Interrupter (GFCI) with manual reset connected to a 9 foot long cord.

    Eyewash Spray Head Assembly: Two GS-Plus™ spray heads. Each head has a “flip top” dust cover, internal flow control and filter.

    Eyewash Valve: 1/2” IPS chrome plated brass three-way self-draining stay-open ball valve with stainless steel flag handle. Pressure regulator controls eyewash flow to 0.65 GPM for 15 minutes.

    Drench Hose Unit: Auxiliary hand-held drench hose for rinsing eyes, face or body. Unit has single GS-Plus™ spray-type outlet head, self-closing valve with squeeze handle, and 6 ft. reinforced PVC hose.

    Operation: To operate unit, fill with clean potable water and add bacteriostatic additive (supplied with unit). Additive protects against growth of bacteria, fungus, algae and acanthamoeba. After filling with water, pressurize unit to 80 PSI. If necessary, adjust pressure regulator to achieve maximum flow for 15 minutes. Unit should be inspected regularly and water should be changed at least once every six months. Filling instructions included.

    Weight: 41.5 lbs. empty, 124.8 lbs. filled.

    Sign: ANSI compliant identification sign permanently affixed to insulated jacket.

    Quality Assurance: Unit is fully assembled, pressurized and water tested at the factory. Unit is depressurized and emptied prior to shipping. Some assembly required in the field.

    Read more
    Quick View
  •
    Read more
    Quick View

    GUARDIAN CLEAR VINYL COVER FOR AQUAGUARD 16 GALLON PORTABLE EYEWASH MODEL : G1540CVR

    Cover, EQUIPMENT G1540CVR G1540CVR, SKU: G0657091 Product Details Flange, Features In.
    Mounting With and Drench About Us small business stay competitive! We offering of products low prices. historically been at disadvantage who at of their size. want change Zoro has the “big we offer one There are discount structures to understand.
    Every the same an you to or one We have our headquarters in Grove, petitioning town rename (We’re Buffaloes.) Like believe that always put our customers first.

    Read more
    Quick View
  •
    Read more
    Quick View

    GUARDIAN TEMPERING VALVE, 44 GALLON CAPCITY MODEL : G3800LF

    APPLICATION NOTE: These products were discontinued in September, 2021.  Repair parts are no longer available. The Guardian G604X series of valve cabinets is a higher capacity, lower maintenance, and more affordable tempering valve that is designed as the successor to the G3800LF.

    The G3802LF is a G3800LF tempering valve contained within a surface-mounted steel cabinet.  The G3807LF is a recess-mounted cabinet (select the “recess mount” checkbox above to select).  This series of valves is suitable for use with a single installation of emergency showers and safety stations, and with multiple installations of emergency shower, eyewash, eye/face wash, dual purpose eyewash/drench hose, drench hose and safety station units. The G3800LF valve is available in two additional configurations.

    We carry a full line of tempering valves ranging in capacities from 6 to 81 gallons per minute (GPM). The valve must be properly matched to the flow capacity of the safety station in order to deliver water within the tepid range.

    Read more
    Quick View
  •
    Read more
    Quick View

    GUARDIAN RECESSED SAFETY STATION WITH DRAIN PAN, EXPOSED SHOWER HEAD MODEL : GBF2150

    Application: Recessed barrier-free eye/face wash and shower safety station with ceiling mounted exposed shower head and drain pan. Stainless steel cover provides attractive appearance and protects unit when not in use. When activated, cover serves as pan to collect waste water and return it into unit for drainage.

    ADA Compliance: When installed at recommended mounting heights, unit complies with ADA requirements for accessibility by handicapped persons.

    Shower Head: 10″ diameter stainless steel with 20 GPM flow control. Furnished with vertical supply pipe and ceiling escutcheon for mounting shower head at desired height below finished ceiling.

    Shower Valve: 1″ IPS brass stay-open ball valve with stainless steel “panic bar” actuator.

    Cover/Drain Pan: 16 gauge stainless steel combination cover and drain pan. Grasping “panic bar” handle and opening cover pulls spray head assembly down from vertical to horizontal position, activating water flow. While unit is in operation, waste water is collected in drain pan and returned into cabinet for drainage. Unit remains in operation until cover is returned to closed position.

    Eye/Face Wash Spray Head Assembly: Two FS-Plus™ spray heads mounted on supply arms. Each spray head has individually adjustable flow control and filter to remove impurities from water flow.

    Eye/Face Wash Valve: 1/2″ IPS brass plug-type valve with O-ring seals. Furnished with in-line strainer to protect valve from debris and foreign matter.

    Mounting: 16 gauge stainless steel cabinet with flange featuring 3/8″ return for recessed mounting in wall. Unit fits in standard 3-5/8″ deep wall.

    Pipe And Fittings: Exposed pipe and escutcheon are brushed stainless steel.

    Supply: 1″ NPT female inlet.

    Waste: 2″ NPT female outlet.

    Sign: ANSI-compliant identification sign.

    Quality Assurance: Unit is completely assembled and water tested prior to shipment.

    Read more
    Quick View
  • Eyewash, Wall Mounted, Plastic Bowl, Arca Timur
    Read more
    Quick View

    Guardian Eyewash, Wall Mounted, Plastic Bowl MODEL : G1814P

    Application: Eyewash with plastic bowl for wall mounting. Two GS-Plus™ spray-type outlet heads deliver a flood of water for rinsing eyes.

    Spray Head Assembly: Two GS-Plus™ spray heads. Each head has a “flip top” dust cover, internal flow control and filter to remove impurities from the water flow.

    Valve: 1/2″ IPS chrome plated brass stay-open ball valve. Valve is US-made with chrome plated brass ball and PTFE seals.

    Bowl: 11-3/4″ diameter orange ABS plastic.

    Mounting: Heavy duty cast aluminum wall bracket with corrosion resistant powder coated finish.

    Supply: 1/2″ NPT female inlet.

    Waste: 1-1/4″ NPT female outlet.

    Sign: ANSI-compliant identification sign.

    Quality Assurance: Unit is completely assembled and water tested prior to shipment.

    Read more
    Quick View
  • Test Kit for Emergency Showers and Safety Stations, Arca Timur
    Read more
    Quick View

    GUARDIAN TEST KIT FOR EMERGENCY SHOWERS AND SAFETY STATIONS MODEL : AP250-005

    Application: Test emergency equipment for proper operation. Includes Tyvek® chute and pail to contain tested water flow and prevent spillage.

    Note: ANSI Z358.1 requires weekly activation of emergency equipment for a period long enough to verify operation and ensure flushing fluid is available.

    Contents: 48″ telescopic aluminum pole, 11-1/2″ diameter Tyvek® test chute, 5 gallon plastic pail, and eyewash tester.

    Read more
    Quick View